Kyocera Mita 1900N - B/W Laser Printer Скачать руководство пользователя страница 37

Страница: 37 / 286

Printing Test Pages

1-23

Received Data Dumping

It is possible to print data received by the printer as hexadecimal code for

the purposes of debugging programs and files.

Press the

MENU

key.

Press the or key repeatedly until

Others >

appears.

Press the

key.

Press the or key repeatedly until

> Print HEX-DUMP

appears.

Press the

ENTER

key. A question mark (

) appears.

Press the

ENTER

key again.

Processing

appears for a second, and

then

Waiting

appears.

Send data to be dumped to the printer. The message

Processing

will be displayed during receiving the data.

Once the dumped data you require has been output, it is possible to

cancel the printing of any further dumped data by taking the printer

offline by pressing the

key and then pressing the

CANCEL

key.

Once all data has been received, the message

Waiting

will appear.

Press the

key to finish printing.

Others

>Print HEX-DUMP

>Print HEX-DUMP?

Processing

Waiting

Содержание 1900N - B/W Laser Printer































































































































































































































































































Результаты поиска

Содержание 1900N - B/W Laser Printer

Отзывы:

Похожие инструкции для 1900N - B/W Laser Printer

Бренды по названию

Популярные бренды

Kyocera Mita 1900N - B/W Laser Printer, Руководство по эксплуатации

Результаты поиска

Содержание 1900N - B/W Laser Printer

Отзывы:

Похожие инструкции для 1900N - B/W Laser Printer

Бренды по названию

Популярные бренды