Kyocera Mita 1900N - B/W Laser Printer Скачать руководство пользователя страница 182

Страница: 182 / 286

Installing Option Units

B-12

DU-60 Duplexer

Install the option duplexer immediately below the printer. By combining

the two binding modes (short edge bind and long edge bind) with the two

printing orientations (portrait and landscape), duplex printing is possible

in four different methods. Duplex printing can be specified from the

application (printer driver).

Remove the nine tapes and the pad from the duplexer.

While pushing the rear cover release lever inward, remove the

duplexer rear cover.

Turn off the printer and disconnect the power cord and printer cable.

Содержание 1900N - B/W Laser Printer































































































































































































































































































Результаты поиска

Содержание 1900N - B/W Laser Printer

Отзывы:

Бренды по названию

Популярные бренды

Kyocera Mita 1900N - B/W Laser Printer, Руководство по эксплуатации

Результаты поиска

Содержание 1900N - B/W Laser Printer

Отзывы:

Бренды по названию

Популярные бренды