Kyocera Mita 1900N - B/W Laser Printer Скачать руководство пользователя страница 120

Страница: 120 / 286

Configuration

1-106

Setting the Auto Continue Recovery Time

Follow the procedure given below to change the recovery time for Auto

Continue.

Press the

MENU

key.

Press the or key repeatedly until

Others >

appears.

Press the

key.

Press the or key repeatedly until

Auto Continue Mode >

appears.

Press the

key and display

>>Auto Continue Timer

Press the

ENTER

key. A blinking cursor (

) appears.

Press the or key to increase or decrease the value of the figure

where the cursor is blinking and set the desired time. The time must

be set between

000

and

495

seconds, in 5-second increments. If set to

000

, printing will be continued immediately without allowing any

time interval. You can use the

and

keys to move the cursor right

and left.

Display the desired time and press the

ENTER

key.

Press the

MENU

key. The message display returns to

Ready

Others

>Auto Continue >

Mode On

>>Auto Continue

Timer 000Sec.

Содержание 1900N - B/W Laser Printer































































































































































































































































































Результаты поиска

Содержание 1900N - B/W Laser Printer

Отзывы:

Бренды по названию

Популярные бренды

Kyocera Mita 1900N - B/W Laser Printer, Руководство по эксплуатации

Результаты поиска

Содержание 1900N - B/W Laser Printer

Отзывы:

Бренды по названию

Популярные бренды