Kyocera Mita 1900N - B/W Laser Printer Скачать руководство пользователя страница 128

Страница: 128 / 286

Special Paper

2-8

Adhesive-Backed Labels

The basic rule for printing on adhesive labels is that the adhesive must

never come into contact with any part of the printer. Adhesive paper

sticking to the drum or rollers will damage the printer.

Be sure to feed label paper from the MP tray. Feeding label paper from a
paper cassette may cause printer failure.

Label paper has a structure comprised of three layers, as shown in the

figure below. The top sheet is printed on. The adhesive layer consists of

pressure-sensitive adhesives. The carrier sheet (also called the linear or

backing sheet) holds the labels until use. Due to the complexity of its

composition, adhesive-backed label paper is particularly likely to give

trouble in printing.

Adhesive label paper must be entirely covered by its top sheet, with no

spaces between the individual labels. Labels with spaces in between are

apt to peel off, causing serious paper jam problems.
Some label paper is manufactured with an extra margin of top sheet

around the edge. Do not remove the extra top sheet from the carrier sheet

until after printing is finished.

Note

Top sheet (white bond paper)

Adhesive
Carrier sheet

Top sheet

Unacceptable

Acceptable

Carrier sheet

Содержание 1900N - B/W Laser Printer































































































































































































































































































Результаты поиска

Содержание 1900N - B/W Laser Printer

Отзывы:

Бренды по названию

Популярные бренды

Kyocera Mita 1900N - B/W Laser Printer, Руководство по эксплуатации

Результаты поиска

Содержание 1900N - B/W Laser Printer

Отзывы:

Бренды по названию

Популярные бренды