KVH Industries TracPhone V3HTS Скачать руководство пользователя страница 4

Страница: 4 / 52

Before you begin, follow these steps to make sure
you have everything you need to complete the
installation.

Unpack the box and ensure it contains

everything shown in Figure 1 and on the

Kitpack Contents List

. Save the packaging for

future use.

Carefully examine all of the supplied parts to

ensure nothing was damaged in shipment.

Gather all of the following tools and

materials that you will need:

• Flat-head and Phillips-head screwdrivers

• Electric drill and 5/16" (8 mm) bit

• 3.5" (89 mm) hole saw

• 1/2" socket and 7/16" socket

• 7/16" open-end torque wrench set to

20 in.-lbs

• Light hammer and center punch

• Adhesive tape

• Silicone sealant, self-vulcanizing tape, or

equivalent

• Eye protection

• Shop towels

• Voltmeter

• Utility knife

• Flush cutters

• Wire stripper/terminal crimper

• File

• Two 75



RF coax cables, “F” connectors,

and associated termination tools (see

page 11)

dome

Antenna

(KVH part no. 02-1860-01)

sepl

Integrated CommBox Modem (ICM)

(KVH part no. 02-2204-01)

Figure 1: TracPhone V3-HTS System Components

Always lift the antenna by the baseplate and

never by the radome or any portion of the

internal antenna assembly (see Figure 1).

IMPORTANT!

• NMEA 0183 talker and interface cable (see

page 16)

• Isolation transformer, if required (see page 18)

• RS422-to-USB adapter

• Laptop PC with the latest TracPhone V3-HTS

ICM/antenna software (.kvh) downloaded from

the KVH Partner Portal (

www.kvh.com/

partners

) and PuTTY, HyperTerminal, or other

terminal emulator installed

Inspect Parts and Get Tools

Содержание TracPhone V3HTS





















































Результаты поиска

Содержание TracPhone V3HTS

Отзывы:

Похожие инструкции для TracPhone V3HTS

Бренды по названию

Популярные бренды

KVH Industries TracPhone V3HTS, Руководство по установке

Результаты поиска

Содержание TracPhone V3HTS

Отзывы:

Похожие инструкции для TracPhone V3HTS

Бренды по названию

Популярные бренды