KVH Industries TracPhone V3HTS Скачать руководство пользователя | Manualshive

Страница: 51 / 52

background image

Regulatory Compliance

European Union Compliance

Hereby, KVH Industries, Inc. declares that the radio equipment type TracPhone V3-HTS is in

compliance with Directive 2014/53/EU. For the full text of the EU Declaration of Conformity, go

to

www.kvh.com/euconformity

Federal Communications Commission Compliance

The TracPhone system complies with Class B of Part 15 of the FCC (Federal
Communications Commission) rules for radiated and conducted emissions.

FCC Identifiers: PPD-AR5B97 (ICM WiFi)

Use Conditions

:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may

cause undesired operation.

Note

:

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. To determine if the
equipment is interfering with radio or television reception, remove or apply power to the
equipment and observe if the interference goes away, or returns, when the unit is off or on. The
user is encouraged to try to correct the interference by one of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.

•

Consult KVH for assistance.

IMPORTANT

:

•

To meet FCC requirements, shielded Ethernet cables are required to connect the ICM to
the ship’s network.

•

This equipment contains no user serviceable parts. Opening this unit will violate the
warranty and may result in this equipment no longer complying with FCC requirements
for Class B digital devices.

«
...
49
50
51
52
»

Содержание TracPhone V3HTS





















































Отзывы:

Нет отзывов

Похожие инструкции для TracPhone V3HTS

Бренд: D-Link Страницы: 4

Бренд: Sirio Antenne Страницы: 2

TRAV'LER DIRECTV RP-SK89

Бренд: Winegard Страницы: 2

Бренд: Blaupunkt Страницы: 8

ETS-Lindgren 3147

Бренд: ESCO Technologies Страницы: 49

Бренд: A.H. Systems Страницы: 14

Бренд: QRPGuys Страницы: 10

Бренд: HyperLink Technologies Страницы: 18

Бренд: ETS-Lindgren Страницы: 23

Бренд: ETS-Lindgren Страницы: 41

Бренд: SteppIR Страницы: 80

Бренд: EAntenna Страницы: 13

Бренд: RSI Страницы: 9

Бренд: Laird Страницы: 2

Бренд: TCi Страницы: 2

Бренд: H3C Страницы: 6

Бренд: Steren Страницы: 2

Бренд: Raymarine Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды