KVH Industries TracPhone V3HTS Скачать руководство пользователя | Manualshive

Страница: 34 / 52

background image

33

Standard Configuration

In a standard configuration, Ethernet ports 1
through 4 and the built-in WAP provide high-
speed Internet access with no user logins or
controls. Internet access is unrestricted. This is
the default configuration. Follow these
additional steps to configure the network.

a.

To enable the ICM’s WAP for wireless access,

follow the steps in “ICM Wireless Settings”

b.

Connect the customer’s computers and/or

other network devices to the ICM (see

Figure 66). You might wish to add an external

WAP (or Wi-Fi router configured for bridge

mode) to supplement Wi-Fi access.

c.

Make sure all computers are configured for

DHCP addressing (see page 43). Devices

connected to the ICM (via Ethernet cables or

Wi-Fi) will receive IP addresses from the ICM

via DHCP. The ICM serves as a router.

NOTE:

By default, the High-speed LAN has a

gateway of 192.168.5.1 and assigns IP addresses in
the 192.168.6.50-150 range. If this configuration
conflicts with an existing onboard network, you may
change the settings at the TracPhone V3-HTS web
interface (go to Settings > Network Settings).

Figure 65: Standard Configuration

Figure 66: Standard Configuration Wiring Example

Mobile
Devices

ICM

Mobile
Devices

Crew PC

User Ethernet

Bridge Ops PC

1 2 3 4

Officers PC

Wi-Fi

(High-speed LAN)

WAP

High-speed LAN

Continued

Configure the Network

19

«
...
32
33
34
35
36
...
»

Содержание TracPhone V3HTS





















































Отзывы:

Нет отзывов

Похожие инструкции для TracPhone V3HTS

Бренд: Eaton Страницы: 60

GPS 17x NMEA 0183 HVS

Бренд: Garmin Страницы: 48

Бренд: Marquant Страницы: 16

Бренд: ADC Страницы: 20

Бренд: EARDATEK Страницы: 92

Бренд: Monster Страницы: 2

Бренд: One for All Страницы: 2

Бренд: KING Страницы: 36

Бренд: ETS-Lindgren Страницы: 12

Бренд: ETS-Lindgren Страницы: 33

Бренд: CUSHCRAFT Страницы: 8

Бренд: SteppIR Страницы: 80

Бренд: RCA Страницы: 7

Бренд: RCA Страницы: 2

Бренд: RCA Страницы: 8

ANT800 - HDTV Antenna - Outdoor

Бренд: RCA Страницы: 16

Yagi Y200 Series

Бренд: ZCG Страницы: 2

Бренд: ZCG Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды