KVH Industries TracPhone V3HTS Скачать руководство пользователя

Страница: 21 / 52

Follow these steps to turn on the system.

Ensure the antenna has a clear, unobstructed

view of the sky.

Apply vessel power to the TracPhone system.

Press the power button on the front of the

ICM (see Figure 32). The button’s light

should illuminate blue.

Measure the AC and DC voltages between

the ground point on the ICM’s rear panel

(chassis ground) and ship’s ground. Make

sure you measure less than 2 VAC/2 VDC.

Wait at least 5 minutes for system startup.

After the startup sequence is complete, verify

that the ICM’s Control Unit status light is lit

solid green and the Antenna and Modem

lights are lit solid or flashing green (see

Figure 33).

Connect your PC to the “User Ethernet 1”

port on the rear panel of the ICM (see

Figure 34).

Turn off the Wi-Fi on your PC and keep it

turned off while connected to the ICM.

Open a web browser on your PC and enter

the following address:

http://minivsat.kvh

Verify that the TracPhone V3-HTS web

interface appears in your browser. If the web

interface is not displayed, enter the ICM’s IP

address

(you can find this address on the LCD:

go to Settings > Network Settings > IP

Assignments)

and

make sure your PC is

configured for DHCP (see page 43).

Figure 32: Power Button

Power Button

Figure 33: Status Lights

ICM

Figure 34: Connecting Your Laptop to the ICM

User Ethernet

ICM

Laptop

1 2 3 4

Turn On the System

Содержание TracPhone V3HTS





















































Результаты поиска

Содержание TracPhone V3HTS

Отзывы:

Похожие инструкции для TracPhone V3HTS

Бренды по названию

Популярные бренды

KVH Industries TracPhone V3HTS, Руководство по установке

Результаты поиска

Содержание TracPhone V3HTS

Отзывы:

Похожие инструкции для TracPhone V3HTS

Бренды по названию

Популярные бренды