KVH Industries TracPhone V3HTS Скачать руководство пользователя

Страница: 9 / 52

There are two options for mounting the ICM:

Option 1

- Inside an equipment rack

Option 2

- To a horizontal surface

NOTE:

You may choose to wait to mount the ICM

until after you have completed all system wiring.

Option 1 – Rack Mount

The ICM is sized to fit a standard 19" (48.26 cm)
rack, occupying 2U of space. Follow these steps
to secure the ICM in an equipment rack.

Attach the supplied strain-relief bracket to

the back of the ICM using four supplied #6-32

screws and washers (see Figure 7).

Insert the ICM into the rack and secure its

front mounting brackets to the rack using

four M6 screws and washers (see Figure 8).

Option 2 – Horizontal Surface Mount

Follow these steps to mount the ICM to a
horizontal surface.

Remove the six #6-32 screws and washers

securing the two rack-mount brackets to the

front of the ICM (see Figure 9). Remove the

brackets.

Attach the supplied strain-relief bracket to

the back of the ICM, and attach the supplied

“L” mounting brackets to the sides of the

ICM, using six supplied #6-32 screws and

washers (see Figure 10).

Mount the ICM to the vessel using fasteners

appropriate for the mounting surface.

Figure 7: Attaching the Strain-Relief Bracket

#6-

2 Screw (x4)

#6 W

sher (x4)

Str

in-Relief

cket

Tie-Wr

Holes (x42)

Figure 8: Securing the ICM in the Rack

stic W

sher (x4)

M6 Screw (x4)

Figure 9: Removing the Rack-Mount Brackets

#6 W

sher (x6)

cket (x2)

Figure 10: Attaching the Mounting and Strain-Relief Brackets

#6 Washer (x6)

#6-32 Screw (x6)

Mounting Bracket (x2)

Ø.156" (Ø3.96 mm)

Mounting Hole (x4)

Strain-Relief Bracket

Mount the ICM

Содержание TracPhone V3HTS





















































Результаты поиска

Содержание TracPhone V3HTS

Отзывы:

Похожие инструкции для TracPhone V3HTS

Бренды по названию

Популярные бренды

KVH Industries TracPhone V3HTS, Руководство по установке

Результаты поиска

Содержание TracPhone V3HTS

Отзывы:

Похожие инструкции для TracPhone V3HTS

Бренды по названию

Популярные бренды