KVH Industries TracPhone V3HTS Скачать руководство пользователя страница 42

Страница: 42 / 52

Gently flare the braid with your fingers (see

Figure 86).

Insert the end of the cable into the connector

body until the dielectric is firmly seated

inside the connector (see Figure 87). Make

sure there is no gap between the knurled end

of the connector and the cable jacket. Also be

sure all braid wires remain on the outside of
the connector.

10.

Trim any excess braid (see Figure 88), if

necessary. The braid should assemble flush to

within 1/16" (1.6 mm) of the connector

shoulder.

11.

Slide the ferrule over the braid until it is flush

against the connector shoulder (see

Figure 89).

Figure 86: Flaring the Braid

Figure 87: Pushing On the Connector

A common installation failure occurs when

the connector is not seated properly onto the

cable. In these cases, the cable’s center

conductor does not fully engage the electrical

contacts inside the connector. To ensure full

engagement, make certain that there is no gap

between the cable jacket and the knurled end

of the connector before you crimp on the

ferrule. You may need to deburr and center

the end of the conductor to achieve a good fit.

IMPORTANT!

Figure 88: Trimming the Braid

Figure 89: Sliding the Ferrule Over the Braid

Continued

Terminating LMR RF Cables

Appendix

Содержание TracPhone V3HTS





















































Результаты поиска

Содержание TracPhone V3HTS

Отзывы:

Похожие инструкции для TracPhone V3HTS

Бренды по названию

Популярные бренды

KVH Industries TracPhone V3HTS, Руководство по установке

Результаты поиска

Содержание TracPhone V3HTS

Отзывы:

Похожие инструкции для TracPhone V3HTS

Бренды по названию

Популярные бренды