KVH Industries TracPhone V3HTS Скачать руководство пользователя страница 37

Страница: 37 / 52

ICM Wireless Settings

With Wi-Fi enabled, vessel devices can connect to
the ICM via its built-in wireless access point
(WAP) and receive IP addresses from the ICM
via DHCP (see Figure 72). Follow these steps to
enable and configure the WAP, if desired by the
customer.

NOTE:

The customer may also change the ICM’s

wireless settings at any time at the mini-VSAT
Manager (

www.mykvh.com

At the TracPhone V3-HTS web interface, click

the

Settings

tab. Then click

Network

Settings

In Wi-Fi Settings, click

Edit

Set the following wireless options, then click

Save

(see Figure 73):

• State:

Select On.

•

SSID

: Enter a unique name for the vessel

network.

•

Protocol

: Select either 802.11b or 802.11g.

•

Security

: Select either security type –

WPA2 or WEP (128-bit).

•

Password/Passphrase

: If you selected

WPA2, enter a password (between 8-20

characters). If you selected WEP, enter a

passphrase (must be 13 characters).

•

Channel

: Keep the default, or select any

channel for wireless communications.

At the confirmation message, click

Save

Figure 72: Wireless DHCP (Example)

ICM

Wi-Fi

Mobile
Devices

192.168.5.100

192.168.5.101

Establishing a wireless connection onboard a

steel vessel might require a special external

WAP and advanced networking expertise.

IMPORTANT!

Figure 73: Wi-Fi Settings on the ICM

Failure to apply security settings will make

the vessel’s wireless network vulnerable to

outside intrusion.

IMPORTANT!

Continued

Configure the Network

Содержание TracPhone V3HTS





















































Результаты поиска

Содержание TracPhone V3HTS

Отзывы:

Похожие инструкции для TracPhone V3HTS

Бренды по названию

Популярные бренды

KVH Industries TracPhone V3HTS, Руководство по установке

Результаты поиска

Содержание TracPhone V3HTS

Отзывы:

Похожие инструкции для TracPhone V3HTS

Бренды по названию

Популярные бренды