Kverneland 2316M Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 60

background image

Parking / disconnection of the
machine

Parking / disconnection of the
machine

Parking / disconnection of the
machine

Parking / disconnection of the
machine

Parking / disconnection of the
machine

Parking / disconnection of the
machine

Parking / disconnection of the
machine

Parking / disconnection of the
machine

Park the machine in the
working position

The machine

should always be parked in the
working position. This prevents
the machine from tipping over
and causing serious accidents.
If the machine tips over, it can
result in serious or even fatal
injuries.

•

Turn the support leg around
and lower it down as shown.

•

Secure the support leg with
the pin.

The machine is disconnected in
the following way:
•

Remove the pin from the lock
device.

•

Check that the lock device is
free of the lock catch on the
machine's hydraulic cylinder.

•

Activate the tractor's
hydraulics and lower the
machine down to the working
position.

•

Pull the parking catch in and
turn the handle.

•

Check that the handle is
locked correctly.

•

Remove the chain between
the top point and the lift arm
on the tractor.

•

Activate the tractor's lift arms
and lower the machine down
to the ground.

•

Disconnect the PTO shaft
from the tractor.

•

Check that the machine's
hydraulic system is not under
pressure.

•

Disconnect the machine's
hydraulic connections.

•

Disconnect the machine from
the tractor.

3.3 Parking / disconnection

25

«
...
23
24
25
26
27
...
»

Содержание 2316M





























































Отзывы:

Нет отзывов

Похожие инструкции для 2316M

Бренд: ACS Страницы: 56

Бренд: Taber Страницы: 27

Бренд: Canta Страницы: 2

Бренд: Panasonic Страницы: 30

Бренд: CAMAG Страницы: 40

Бренд: Ognibene Страницы: 28

Бренд: Hameg Страницы: 24

Бренд: Vaisala Страницы: 118

Бренд: Maico Страницы: 55

Бренд: Maico Страницы: 38

Бренд: Maico Страницы: 2

Бренд: MAHA Maschinenbau Haldenwang Страницы: 13

Бренд: Nellcor Страницы: 161

OXIMAX N-600X Series

Бренд: Nellcor Страницы: 210

Бренд: Oase Страницы: 120

Бренд: OAKWORKS Страницы: 24

Бренд: Rainin Instrument Страницы: 16

Бренд: TC Electronic Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды