Kverneland 2316M Скачать руководство пользователя | Manualshive

Страница: 12 / 60

background image

Explanation safety labels

Explanation safety labels

Explanation safety labels

Explanation safety labels

Explanation safety labels

Explanation safety labels

Explanation safety labels

Explanation safety labels

Ensure no body parts get
caught in the transmission

Guards may not be removed or
opened until the machine has
stopped rotating. The tractor
engine must be stopped, the
ignition key removed and the
handbrake applied.

Risk of serious injury

Risk of

crushing! Never stand behind the
tractor or between the tractor and
the tool. There is a high risk of
serious injury.

Reflective equipment for slow-
moving vehicles – SMV

This

triangular sign must be placed in
the center at the rear of the
tractor or machine, so that it is
clearly visible at all times when
the machine is in the transport
position. This sign is compulsory
for machines that are being
transported at speeds of below
40 km/h (25 mph) on public
roads.

Risk of the tractor overturning

The tractor's gauge must be at
least 1500 mm when driving with
the machine as there is a risk
that the tractor may overturn.

Risk of serious injury

Risk of

crushing! All persons must keep
clear of the machine's operating
area when it is running.

1.3 Safety labels

12

«
...
10
11
12
13
14
...
»

Содержание 2316M





























































Отзывы:

Нет отзывов

Похожие инструкции для 2316M

Бренд: Daavlin Страницы: 13

Бренд: Daavlin Страницы: 27

SATURA SPOT LED PRO

Бренд: Elation Страницы: 41

Бренд: Tapco Страницы: 16

Бренд: Zenbooth Страницы: 40

Visium CytAssist

Бренд: 10x Genomics Страницы: 51

Chromium X Series

Бренд: 10x Genomics Страницы: 5

Бренд: Velocitek Страницы: 81

ABS-Lock X-Flat

Бренд: ABS Страницы: 8

ABS-Lock X-DURCH

Бренд: ABS Страницы: 8

Бренд: ABS Страницы: 8

Бренд: Abus Страницы: 2

Бренд: Abus Страницы: 12

Бренд: Abu Garcia Страницы: 6

Бренд: Raven Страницы: 17

Бренд: Campbell Страницы: 12

Growers Supply 109722

Бренд: FarmTek Страницы: 9

Бренд: Haag-Streit Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды