Kverneland 2316M Скачать руководство пользователя

Страница: 46 / 60

Cutter bar repair

Change of bearing
intermediate gearwheel

Cutter bar repair

Change of bearing
intermediate gearwheel

Cutter bar repair

Change of bearing
intermediate gearwheel

Cutter bar repair

Change of bearing
intermediate gearwheel

•

Remove tool T1 from the gear
wheel and remove all the
broken parts (typically 5
pieces) of the circlip “A”.

NB!

Make sure that all the

broken parts from the circlip is
removed from the intermediate
gear wheel.

•

Place the gear wheel on top of
tool T3.

NB!

The recessed surface has to

be faced upwards.

•

Make sure the gear wheel and
the new bearing is facing the
right way.

NB!

The groove in the bearing

and

in the gear wheel has be faced
downward.

•

Place tool T2 on top of the
gear wheel as shown.

•

Place the new circlip in the
groove on the bearing.

•

Place the bearing in the cone
shaped tool T2.

NB!

The largest diameter of the

tool has to be faced upwards.

5.4.2 Cutter bar – repair instructions

Содержание 2316M





























































Результаты поиска

Содержание 2316M

Отзывы:

Похожие инструкции для 2316M

Бренды по названию

Популярные бренды

Kverneland 2316M, Техническое и сервисное руководство

Результаты поиска

Содержание 2316M

Отзывы:

Похожие инструкции для 2316M

Бренды по названию

Популярные бренды