Kverneland 2316M Скачать руководство пользователя

Страница: 50 / 60

Cutter bar repair

Assembly of bearing house(s)

Cutter bar repair

Assembly of bearing house(s)

Cutter bar repair

Assembly of bearing house(s)

Cutter bar repair

Assembly of bearing house(s)

•

Fit the last bearing unit in the
cutter bar.

NB!

Take care of the timing!

•

Tighten all the bolts on the
bearing units to 90 Nm / 66
ft.lbs. by use of a torque
wrench.

NB! Do not use LOCTITE or
similar product on these bolts

when fitted. Then the bolts will
not able to be removed from the
nut during a disassemble.

•

Provide the bearing units with
new lock plates.

NB!

After removal of the bearing

unit, new lock plates and new
bolts has to be provided when
fitting of the bearing unit.

•

Bend the lock plate around
the head of the nut on all
bolts.

5.4.2 Cutter bar – repair instructions

Содержание 2316M





























































Результаты поиска

Содержание 2316M

Отзывы:

Похожие инструкции для 2316M

Бренды по названию

Популярные бренды

Kverneland 2316M, Техническое и сервисное руководство

Результаты поиска

Содержание 2316M

Отзывы:

Похожие инструкции для 2316M

Бренды по названию

Популярные бренды