Kurabo QuickGene-Auto240L Скачать руководство пользователя страница 65

Страница: 65 / 78

3 Operation Procedures - Full Auto Protocols

QuickGene-Auto240L Operation Manual

(A-5)

After confirming the reading of all sample ID information,

press [

COMPLETE

(A-6)

The number of samples whose

IDs

are read out will be

displayed in a pop-up window. If it is correct, close all

doors and press

[OK]

Note:

Do not take out the sample holder until the automatic

operation is complete after this operation.

Premature removal will cause an error, the sample ID

information will be deleted, and the system will go

back to "<2> Enter Sample Information"

(A-7)

Go to the next section "<3> Enter Collection Information "

B. When Sample ID Reading Function is OFF

Note:

When the sample ID reading function is OFF, refer to "3.5 Preparation of Samples" and set

the sample holders before turning the system power ON.

(B-1)

Press the numeric button corresponding to the number

of set samples.

・

The pressed buttons will be indicated in reversed deep

blue on the operation screen.

・

The selection will be canceled if the pressed button is

pressed again.

・

Pressing A, B or C button will enable selection of all for

each holder row.

(B-2)

Check that the selected button coincides with the

number of set samples and press [OK].

(B-3)

Move on to the next section "<3> Enter Collection

Information"

Содержание QuickGene-Auto240L















































































Результаты поиска

Содержание QuickGene-Auto240L

Отзывы:

Бренды по названию

Популярные бренды

Kurabo QuickGene-Auto240L, Руководство по эксплуатации

Результаты поиска

Содержание QuickGene-Auto240L

Отзывы:

Бренды по названию

Популярные бренды