manualshive.com logo in svg

KTM 65 SX 2012, Руководство пользователя

Поделиться
Скачать
KTM 65 SX 2012 Скачать руководство пользователя страница 54

BRAKES

52

11.15

Checking the rear brake linings

Warning

Danger of accidents

 

Reduced braking efficiency caused by worn brake linings.

–

Change worn brake linings immediately. (Your authorized KTM workshop will be glad to help.)

700424-01

–

Check the brake linings for minimum thickness

.

Minimum thickness

≥

1 mm (

≥

0.04 in)

» If the minimum thickness is less than specified:

–

Change the rear brake linings.

x

(

p. 53)

–

Check the brake linings for damage and cracking.
» If damage or wear is encountered:

–

Change the rear brake linings.

x

(

p. 53)

11.16

Removing rear brake linings

x

Warning

Danger of accident

 

Brake system failure.

–

Maintenance work and repairs must be carried out professionally. (Your authorized KTM workshop will be glad to help.)

–

Remove the rear wheel.

x

(

p. 56)

700428-01

–

Remove lock washer

.

–

Remove screw

.

700430-01

–

Remove the brake linings.

–

Clean brake caliper and brake caliper support.

11.17

Installing the rear brake linings

x

Warning

Danger of accidents

 

Reduced braking efficiency due to oil or grease on the brake discs.

–

Always keep the brake discs free of oil and grease, and clean them with brake cleaner when necessary.

Warning

Danger of accidents

 

Reduced braking efficiency due to use of non-approved brake linings.

–

Brake linings available from accessory suppliers are often not tested and approved for use on KTM vehicles. The construc-
tion and friction factor of the brake linings and therefore the brake power can differ considerably from the original KTM
brake linings. If brake linings are used that differ from the originals, there is no guarantee that they comply with the origi-
nal license. The vehicle no longer corresponds to the condition at delivery, and the warranty is no longer valid.

–

Check the brake discs. (

p. 45)

Содержание 65 SX 2012

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды