manualshive.com logo in svg

KTM 65 SX 2012, Руководство пользователя

Поделиться
Скачать
KTM 65 SX 2012 Скачать руководство пользователя страница 48

BRAKES

46

11.4

Checking front brake fluid level

Warning

Danger of accidents

 

Brake system failure.

–

If the brake fluid level drops below the specified marking or the specified value, this is an indication that the brake system
is leaking or that the brake linings are completely worn down. Check the brake system and do not continue riding. (Your
authorized KTM workshop will be glad to help.)

Warning

Skin irritation

 

Brake fluid can cause skin irritation on contact.

–

Avoid contact with skin and eyes, and keep out of the reach of children.

–

Wear suitable protective clothing and goggles.

–

If brake fluid comes into contact with the eyes, flush the eyes thoroughly with water and consult a physician immediately.

Warning

Danger of accidents

 

Reduced braking effect caused by old brake fluid.

–

Change the brake fluid of the front and rear brake according to the service schedule. (Your authorized KTM workshop will
be glad to help.)

Warning

Environmental hazard

 

Hazardous substances cause environmental damage.

–

Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.

Info

Never use DOT 5 brake fluid! It is silicone-based and purple in color. Oil seals and brake lines are not designed for DOT 5
brake fluid.
Avoid contact between brake fluid and painted parts. Brake fluid attacks paint!
Use only clean brake fluid from a sealed container.

C00031-10

–

Move the brake fluid reservoir mounted on the handlebar to a horizontal position.

–

Remove screws

.

–

Remove cover

with membrane

.

–

Check the brake fluid level.

Brake fluid level under top level of con-
tainer

5 mm (0.2 in)

» If the brake fluid level does not meet specifications:

–

Add front brake fluid.

x

(

p. 46)

–

Position the cover with the membrane. Mount and tighten the screws.

Info

Clean up overflowed or spilt brake fluid immediately with water.

11.5

Adding front brake fluid

x

Warning

Danger of accidents

 

Brake system failure.

–

If the brake fluid level drops below the specified marking or the specified value, this is an indication that the brake system
is leaking or that the brake linings are completely worn down. Check the brake system and do not continue riding. (Your
authorized KTM workshop will be glad to help.)

Warning

Skin irritation

 

Brake fluid can cause skin irritation on contact.

–

Avoid contact with skin and eyes, and keep out of the reach of children.

–

Wear suitable protective clothing and goggles.

–

If brake fluid comes into contact with the eyes, flush the eyes thoroughly with water and consult a physician immediately.

Содержание 65 SX 2012

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды