manualshive.com logo in svg

KTM 65 SX 2012, Руководство пользователя

Поделиться
Скачать
KTM 65 SX 2012 Скачать руководство пользователя страница 50

BRAKES

48

C00032-01

–

Remove the brake linings.

–

Clean brake caliper and brake caliper support.

11.8

Installing the front brake linings

x

Warning

Danger of accidents

 

Reduced braking efficiency due to oil or grease on the brake discs.

–

Always keep the brake discs free of oil and grease, and clean them with brake cleaner when necessary.

Warning

Danger of accidents

 

Reduced braking efficiency due to use of non-approved brake linings.

–

Brake linings available from accessory suppliers are often not tested and approved for use on KTM vehicles. The construc-
tion and friction factor of the brake linings and therefore the brake power can differ considerably from the original KTM
brake linings. If brake linings are used that differ from the originals, there is no guarantee that they comply with the origi-
nal license. The vehicle no longer corresponds to the condition at delivery, and the warranty is no longer valid.

–

Check the brake discs. (

p. 45)

C00032-01

–

Insert the brake linings.

Info

Ensure that the brake linings are correctly positioned in the retaining spring.

C00034-10

–

Mount and tighten screw

.

Guideline

Screw, brake linings

M6

10 Nm
(7.4 lbf ft)

Lock
washer (0799040009)

–

Mount lock washer

.

–

Install the front wheel.

x

(

p. 55)

11.9

Changing the front brake linings

x

Warning

Skin irritation

 

Brake fluid can cause skin irritation on contact.

–

Avoid contact with skin and eyes, and keep out of the reach of children.

–

Wear suitable protective clothing and goggles.

–

If brake fluid comes into contact with the eyes, flush the eyes thoroughly with water and consult a physician immediately.

Warning

Danger of accidents

 

Reduced braking effect caused by old brake fluid.

–

Change the brake fluid of the front and rear brake according to the service schedule. (Your authorized KTM workshop will
be glad to help.)

Warning

Environmental hazard

 

Hazardous substances cause environmental damage.

–

Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.

Содержание 65 SX 2012

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды