manualshive.com logo in svg

KTM 65 SX 2012, Руководство пользователя

Поделиться
Скачать
KTM 65 SX 2012 Скачать руководство пользователя страница 36

MAINTENANCE WORK ON THE CHASSIS

34

10.21

Mounting the seat

300634-10

–

Hook the seat onto screw

and lower the seat at the rear while pushing it forward.

Projection

hooks into the fuel tank.

300633-11

–

Close quick release

.

10.22

Removing the air filter

x

Note

Engine failure

 

Unfiltered intake air has a negative effect on the service life of the engine.

–

Never ride the vehicle without an air filter since dust and dirt can get into the engine and result in increased wear.

Warning

Environmental hazard

 

Hazardous substances cause environmental damage.

–

Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.

–

Remove the seat. (

p. 33)

700441-01

–

Unhook the air filter holder

and swing it to the side. Remove the air filter with

the air filter support.

–

Remove the air filter from the air filter support.

10.23

Installing the air filter

x

100818-10

–

Mount the clean air filter onto the air filter support.

–

Grease the air filter in area

.

Long-life grease (

p. 81)

Содержание 65 SX 2012

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды