manualshive.com logo in svg

KTM 65 SX 2012, Руководство пользователя

Поделиться
Скачать
KTM 65 SX 2012 Скачать руководство пользователя страница 8

IMPORTANT INFORMATION

6

Environment

Motorcycling is a wonderful sport and we naturally hope that you and your child will be able to enjoy it to the fullest. However, it is a
potential problem for the environment and can lead to conflicts with other persons. But if you use your motorcycle responsibly, you
can ensure that such problems and conflicts do not have to occur. To protect the future of motorcycle sport, make sure that your child
uses the motorcycle legally, display environmental consciousness, and respect the rights of others.

Notes/warnings

Pay close attention to the notes/warnings.

Info

Various information and warning labels are affixed to the vehicle. Do not remove information/warning labels. If they are miss-
ing, you or others may not recognize potential hazards and may therefore be injured.

Grades of risks

Danger

Identifies a danger that will immediately and invariably lead to fatal or serious permanent injury if the appropriate measures
are not taken.

Warning

Identifies a danger that is likely to lead to fatal or serious injury if the appropriate measures are not taken.

Caution

Identifies a danger that may lead to minor injuries if the appropriate measures are not taken.

Note

Identifies a danger that will lead to considerable machine and material damage if the appropriate measures are not taken.

Warning

Identifies a danger that will lead to environmental damage if the appropriate measures are not taken.

Owner's manual

–

Carefully read this owner's manual in its entirety together with your child before letting your child ride the motorcycle for the first
time. It contains a lot of information and tips to help you and your child operate and handle the motorcycle. Only then will you
find out how to customize the motorcycle ideally for your child's use and how to protect your child from injury. The owner's manual
also contains important information on servicing the motorcycle.

–

The owner's manual is an important component of the motorcycle and should be handed over to the new owner if the vehicle is
sold.

Содержание 65 SX 2012

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды