manualshive.com logo in svg

KTM 65 SX 2012, Руководство пользователя

Поделиться
Скачать
KTM 65 SX 2012 Скачать руководство пользователя страница 12

CONTROLS

10

5.1

Clutch lever

C00038-10

The clutch lever

is fitted on the left side of the handlebar.

The clutch is hydraulically operated and self-adjusting.

5.2

Hand brake lever

C00030-10

Hand brake lever

is fitted on the right side of the handlebar.

The hand brake lever is used to activate the front brake.

5.3

Throttle grip

C00027-10

Throttle grip

is fitted on the right side of the handlebar.

5.4

Kill switch

C00039-10

Kill switch

is fitted on the left side of the handlebar.

Possible states

• Kill switch

in basic position

–

In this position, the ignition circuit is closed, and

the engine can be started.

• Kill switch

pressed

–

In this position, the ignition circuit is interrupted, a run-

ning engine stops, and a non-running engine will not start.

5.5

Opening the filler cap

Danger

Fire hazard

 

Fuel is highly flammable.

–

Never refuel the vehicle near open flames or burning cigarettes, and always switch off the engine first. Be careful that no
fuel is spilt, especially on hot vehicle components. Clean up spilt fuel immediately.

–

Fuel in the fuel tank expands when warm and can escape if the tank is overfilled. See the notes on refueling.

Warning

Danger of poisoning

 

Fuel is poisonous and a health hazard.

–

Avoid contact between fuel and skin, eyes and clothing. Do not inhale fuel vapors. If fuel gets into your eyes, rinse immedi-
ately with water and contact a doctor. Wash affected skin areas immediately with soap and water. If fuel is swallowed, con-
tact a doctor immediately. Change clothing that has come into contact with fuel. Store fuel in a suitable canister according
to regulations and keep it out of the reach of children.

Содержание 65 SX 2012

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды