manualshive.com logo in svg

KTM 65 SX 2012, Руководство пользователя

Поделиться
Скачать
KTM 65 SX 2012 Скачать руководство пользователя страница 64

TUNING THE ENGINE

62

14.1

Checking the play in the throttle cable

700453-10

–

Check the throttle grip for smooth operation.

–

Move the handlebar to the straight-ahead position.

–

Push back sleeve

.

–

Pull back the throttle cable casing until you sense a resistance.

–

Now check throttle cable play

.

Play in gas throttle cable

3… 5 mm (0.12… 0.2 in)

» If the throttle cable play does not meet specifications:

–

Adjust the play in the throttle cable.

x

(

p. 62)

–

Slide on sleeve

. Check the throttle grip for smooth operation.

14.2

Adjusting the play in the throttle cable

x

700453-01

–

Move the handlebar to the straight-ahead position.

–

Push back sleeve

.

–

Loosen nut

. Turn adjusting screw

in as far as possible.

–

Turn the adjusting screw so that there is play

at the outer casing of the throttle

cable.
Guideline

Play in gas throttle cable

3… 5 mm (0.12… 0.2 in)

–

Tighten nut.

–

Slide on sleeve

. Check the throttle grip for smooth operation.

14.3

Carburetor - idle

700457-01

The idle setting of the carburetor has a big influence on the starting behavior, stable
idling and the response to throttle opening. That means that an engine with a correctly
set idle speed is easier to start than if the idle is set wrongly.

Info

The carburetor and its components are subject to increased wear caused by
engine vibration. Wear can result in malfunctioning.

The idle speed is adjusted with adjusting screw

.

The idle mixture is adjusted with idle adjusting screw

.

14.4

Carburetor - adjusting the idle speed

x

700457-01

–

Screw in idle air adjusting screw

all the way and turn it to the specified basic

position.
Guideline

Idle air adjusting screw

Open

3.5 turns

–

Run the engine until warm.
Guideline

Warm-up time

≥

5 min

Danger

Danger of poisoning

 

Exhaust gases are poisonous and inhaling them may

result in unconsciousness and/or death.

–

When running the engine, always make sure there is sufficient ventila-
tion, and do not start or run the engine in an enclosed space without an
effective exhaust extraction system.

–

Adjust the idle speed with the adjusting screw

.

Guideline

Choke function deactivated

–

The choke lever is pushed up all the way.

(

p. 11)

Idle speed

1,400… 1,500 rpm

Содержание 65 SX 2012

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды