KTM 65 SX 2012 Скачать руководство пользователя страница 71

Страница: 71 / 88

TROUBLESHOOTING

Faults

Possible cause

Action

Engine turns but does not start

Operating error

–

Go through the steps of starting the engine.

(

p. 15)

Motorcycle was out of use for a long
time and there is old fuel in the float
chamber

–

Empty the carburetor float chamber.

(

p. 63)

Fuel feed interrupted

–

Check the fuel tank breather.

–

Clean the fuel tap.

–

Check/set the carburetor components.

Spark plug oily or wet

–

Clean and dry the spark plug, or change it if
necessary.

Electrode distance (plug gap) of spark
plug too wide

–

Adjust the plug gap.
Guideline
Spark plug electrode gap
0.60 mm (0.0236 in)

Fault in ignition system

–

Check the ignition system.

–

Adjust the ignition.

Short circuit cable in wiring harness
frayed, kill switch defective

–

Check the kill switch.

Socket connector or ignition coil is
loose or oxidized

–

Clean the socket connector and treat it with
contact spray.

Water in carburetor or jets blocked

–

Check/set the carburetor components.

Engine has no idle

Idling jet blocked

–

Check/set the carburetor components.

Adjusting screws on carburetor dis-
torted

–

Carburetor - adjust the idle speed.

(

p. 62)

Spark plug defective

–

Change spark plug.

Ignition system defective

–

Check the ignition coil.

–

Check the spark plug connector.

Engine does not speed up

Carburetor running over because float
needle dirty or worn

–

Check/set the carburetor components.

Loose carburetor jets

–

Check/set the carburetor components.

Fault in ignition system

–

Check the ignition system.

–

Adjust the ignition.

Engine has too little power

Fuel feed interrupted

–

Check the fuel tank breather.

–

Clean the fuel tap.

–

Check/set the carburetor components.

Air filter very dirty

–

Clean the air filter and air filter box.

(

p. 35)

Exhaust system leaky, deformed or
too little glass fiber yarn filling in
main silencer

–

Check exhaust system for damage.

–

Change the glass fiber yarn filling of the main
silencer.

(

p. 36)

Fault in ignition system

–

Check the ignition system.

–

Adjust the ignition.

Diaphragm or reed valve housing
damaged

–

Check the diaphragm and reed valve housing.

Noticeable wear

–

Overhaul the engine.

Engine stalls or is popping into the
carburetor

Lack of fuel

–

Turn the knurled screw on the fuel tap all the
way counterclockwise.

–

Fill up with fuel. (

p. 17)

Engine takes in bad air

–

Check the intake flange and carburetor for
tightness.

Socket connector or ignition coil is
loose or oxidized

–

Clean the socket connector and treat it with
contact spray.

Engine overheats

Too little coolant in cooling system

–

Check the cooling system for leakage.

–

Check the coolant level. (

p. 60)

Too little air stream

–

Switch off engine when standing.

Содержание 65 SX 2012

























































































Результаты поиска

Содержание 65 SX 2012

Отзывы:

Бренды по названию

Популярные бренды

KTM 65 SX 2012, Руководство пользователя

Результаты поиска

Содержание 65 SX 2012

Отзывы:

Бренды по названию

Популярные бренды