manualshive.com logo in svg

KTM 65 SX 2012, Руководство пользователя

Поделиться
Скачать
KTM 65 SX 2012 Скачать руководство пользователя страница 38

MAINTENANCE WORK ON THE CHASSIS

36

10.26

Installing the main silencer

700444-01

–

Mount the main silencer with the rubber sleeve

.

–

Position the wide collar bushing

and the narrow collar bushing

.

700442-10

–

Mount and tighten screw

.

Guideline

Remaining screws, chassis

M6

10 Nm (7.4 lbf ft)

10.27

Changing the glass fiber yarn filling of the main silencer

x

Warning

Danger of burns

 

The exhaust system gets very hot when the vehicle is driven.

–

Allow the exhaust system to cool down. Do not touch hot components.

Info

Over a period, the fibers of the insulating material vanish into the air, and the silencer "burns out".
Not only is the noise level higher, the performance characteristic changes.

–

Remove the main silencer. (

p. 35)

700443-01

–

Remove screws

of locking cap

. Remove locking cap and outer tube

.

–

Pull the glass fiber yarn filling

from the inner tube.

–

Clean the parts that are to be reinstalled.

–

Mount the new glass fiber yarn filling on the inner tube.

–

Slide the outer tube over the glass fiber yarn filling.

–

Insert the locking cap into the outer tube.

–

Mount and tighten the screws with the toothed washers.
Guideline

Remaining screws, chassis

M6

10 Nm (7.4 lbf ft)

–

Install the main silencer. (

p. 36)

10.28

Dismounting the fuel tank

x

Danger

Fire hazard

 

Fuel is highly flammable.

–

Never refuel the vehicle near open flames or burning cigarettes, and always switch off the engine first. Be careful that no
fuel is spilt, especially on hot vehicle components. Clean up spilt fuel immediately.

–

Fuel in the fuel tank expands when warm and can escape if the tank is overfilled. See the notes on refueling.

Warning

Danger of poisoning

 

Fuel is poisonous and a health hazard.

–

Avoid contact between fuel and skin, eyes and clothing. Do not inhale fuel vapors. If fuel gets into your eyes, rinse immedi-
ately with water and contact a doctor. Wash affected skin areas immediately with soap and water. If fuel is swallowed, con-
tact a doctor immediately. Change clothing that has come into contact with fuel. Store fuel in a suitable canister according
to regulations and keep it out of the reach of children.

Содержание 65 SX 2012

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды