manualshive.com logo in svg

KTM 65 SX 2012, Руководство пользователя

Поделиться
Скачать
KTM 65 SX 2012 Скачать руководство пользователя страница 58

WHEELS, TIRES

56

12.3

Removing the rear wheel

x

–

Raise the motorcycle with a lift stand. (

p. 26)

–

Remove the chain guard. (

p. 38)

700439-01

–

Remove nut

.

–

Remove washer

and chain adjuster

.

100819-10

–

Withdraw the wheel spindle

only enough to allow the rear wheel to be pushed

forward.

–

Push the rear wheel forward as far as possible. Remove the chain from the rear
sprocket.

–

Holding the rear wheel, withdraw the wheel spindle. Take the rear wheel out of the
swingarm.

Info

Do not operate the foot brake when the rear wheel is removed.
Always lay the wheel down in such a way that the brake disc is not dam-
aged.

12.4

Installing the rear wheel

x

Warning

Danger of accidents

 

Reduced braking efficiency due to oil or grease on the brake discs.

–

Always keep the brake discs free of oil and grease, and clean them with brake cleaner when necessary.

100819-11

–

Check the wheel bearing for damage and wear.
» If the wheel bearing is broken or worn:

–

Change the wheel bearing.

x

–

Clean and grease wheel spindle

.

Long-life grease (

p. 81)

–

Lift the rear wheel into the swingarm and position it.

–

Insert the wheel spindle

with washer

and chain adjuster

.

–

Apply the chain.

–

Position chain adjuster

and push the wheel spindle all the way in.

700439-10

–

Position chain adjuster

and washer

. Mount nut

, but do not tighten it yet.

–

Make sure that the chain adjusters are fitted correctly on the adjusting screws.

–

Check the chain tension. (

p. 39)

–

Tighten nut

.

Guideline

Nut, rear wheel spindle

M12x1

40 Nm
(29.5 lbf ft)

–

Operate the foot brake lever repeatedly until the brake linings lie on the brake disc
and there is a pressure point.

–

Install the chain guard. (

p. 38)

–

Remove the motorcycle from the lift stand. (

p. 26)

Содержание 65 SX 2012

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды