manualshive.com logo in svg

KTM 65 SX 2012, Руководство пользователя

Поделиться
Скачать
KTM 65 SX 2012 Скачать руководство пользователя страница 41

MAINTENANCE WORK ON THE CHASSIS

39

10.32

Checking chain dirt

400678-01

–

Check the chain for coarse dirt accumulation.
» If the chain is very dirty:

–

Clean the chain. (

p. 39)

10.33

Cleaning the chain

Warning

Danger of accidents

 

Oil or grease on the tires reduces their grip.

–

Remove oil and grease with a suitable cleaning material.

Warning

Danger of accidents

 

Reduced braking efficiency due to oil or grease on the brake discs.

–

Always keep the brake discs free of oil and grease, and clean them with brake cleaner when necessary.

Warning

Environmental hazard

 

Hazardous substances cause environmental damage.

–

Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.

Info

The service life of the chain depends largely on its maintenance.

400725-01

–

Clean the chain regularly and then treat with chain spray.

Chain cleaner (

p. 81)

Off-road chain spray (

p. 81)

10.34

Checking the chain tension

Warning

Danger of accidents

 

Danger caused by incorrect chain tension.

–

If the chain tension is too high, the components of the secondary power train (chain, engine sprocket, rear sprocket, bear-
ings in transmission and rear wheel) are under additional load. Apart from premature wear, in extreme cases the chain can
rupture or the countershaft of the transmission can break. On the other hand, if the chain is loose, it can fall off the engine
sprocket or the rear sprocket and block the rear wheel or damage the engine. Check the chain tension and correct if neces-
sary.

–

Remove the chain guard. (

p. 38)

–

Raise the motorcycle with a lift stand. (

p. 26)

Содержание 65 SX 2012

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды