Kronoterm WP4 LF-502 Скачать руководство пользователя страница 32

Страница: 32 / 56

ID.: 17-16-20-2979-10

3.2018

7. Controller

The interface of device controller OPTITRONIC 2 consists of a colour LCD display and four
function keys for operation.

back / screensaver

increase value

forward / confirm / menu

decrease value

7.1 Basic Window

7.1.1 Sanitary Water Temperature

system statuses

LCD screen displays currently
measured

sanitary

water

temperature

sanitary

water

temperature

7.1.2 System statuses

Display current device operation. The statuses show the active operation programme, functioning of
individual system components and potential errors and warnings.

Legend of system statuses:

Operation of compressor and backup source

Alternative / additional source state

Device generator heating sanitary water

Internal electric heater active

Backup source programme active

External source active

Device on standby

Internal heater and external source active

Device in startup mode

Active programme

Warningsa nd defects

Anti-freeze programme active

External input influencing operation

Defrosting programme active

Warning

Quick water heating programme active

Error

Overheating - anti-legionella programme active

Operation mode

Holiday programme active

COMFORT PLUS programme active

NORMAL programme active

ADDITIONAL SOURCE programme active

ECO programme active

OFF programme active

COMFORT programme active

PHOTOVOLTAICS (PV) programme
active

Содержание WP4 LF-502

























































Результаты поиска

Содержание WP4 LF-502

Отзывы:

Похожие инструкции для WP4 LF-502

Бренды по названию

Популярные бренды

Kronoterm WP4 LF-502, Инструкция по использованию и установке

Результаты поиска

Содержание WP4 LF-502

Отзывы:

Похожие инструкции для WP4 LF-502

Бренды по названию

Популярные бренды