Kronoterm WP4 LF-502 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 56

background image

ID.: 17-16-20-2979-10

28

3.2018

5.9 Electric Connection

Electric connection of the supply cable, external signal, additional temperature probe, and
additional heater is done under the cover on the front of the device. To access electrical
connections the front cover must be removed as shown below:

Figure 10: Front cover removal

WARNING

Connection  of  the  device  to  the  power  grid  must  take  place  in  accordance  with
standards  for  connection  to  electrical  grids.  The  device  must  be  connected  to  the
electrical grid via a shutdown element, built into the electrical installation according
to  valid  regulations.  The  shutdown  element  must  separate  all  contacts  under  the
conditions of overload category III.

DANGER

The device must be connected to the electricity supply where the RCD (FID) switch
of type A is installed.

All electrical connections are carried out on the bottom holder, where electrical pins with
cable release pins are prepared.

«
...
26
27
28
29
30
...
»

Содержание WP4 LF-502

























































Отзывы:

Нет отзывов

Похожие инструкции для WP4 LF-502

Бренд: EarthLinked Страницы: 6

Бренд: Warmtech Страницы: 28

Бренд: Gardena Страницы: 17

Бренд: Gardena Страницы: 12

Бренд: York Страницы: 14

Бренд: Cadet Страницы: 16

Бренд: EQUATION Страницы: 12

Q HEAT R Series

Бренд: CANVAC Страницы: 88

Бренд: CTC Union Страницы: 2

Бренд: NewAir Страницы: 11

Бренд: JLF Страницы: 5

Бренд: Warmtec Страницы: 60

ERGO Tools E-KTP 3070

Бренд: Pattfield Страницы: 56

Бренд: DèLonghi Страницы: 7

Бренд: Vornado Страницы: 9

Бренд: Wacker Neuson Страницы: 68

Бренд: Uberhaus Страницы: 7

Бренд: NuTone Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды