Kronoterm WP4 LF-502 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 56

background image

ID.: 17-16-20-2979-10

8

3.2018

WARNING

The device must not be stacked or have items lean against it. If, while the device is
operational, the water temperature exceeds 80

°C, contact service.

WARNING

Ensure, that the device does not represent a danger to anyone. Access to
device must be prevented to children and uninstructed persons.

WARNING

Do not place the device into a room where it could not be removed from.
Later building around it or placement of other obstructions by the device is
forbidden.

WARNING

Service and maintenance of the device may only be carried out by a service
technician, authorised by the manufacturer. In case of a defect, first contact
the installation technician that installed the device.

WARNING

Never clean the device with cleaning agents which contain sand, soda, acid
or chlorides, as they can damage the surface of the device.

WARNING

The  device  contains  the  coolant  R134a,  which,  compliant  with  the  Kyoto
Protocol,  is  listed  among  greenhouse  gasses.  Thus  work  on  the  device  is
only  permitted  to  authorised  persons  for  handling  of  coolant  as  defined  by
the law in force. During interventions into the device, escape of coolant into
the atmosphere must be prevented.

WARNING

In avoidance of dangers, a damaged power cable may only be replaced by
the manufacturer or an authorised installation technician..

«
...
6
7
8
9
10
...
»

Содержание WP4 LF-502

























































Отзывы:

Нет отзывов

Похожие инструкции для WP4 LF-502

Бренд: Lasko Страницы: 4

Бренд: Wacker Neuson Страницы: 162

Бренд: U-Line Страницы: 3

Бренд: Homa Страницы: 24

TV 301 Navigator 969-8918

Бренд: Varian Страницы: 55

Home FKIR 350 WIFI

Бренд: Somogyi Elektronic Страницы: 24

Бренд: KDK Страницы: 17

Бренд: Varma Tec Страницы: 20

Бренд: LEYBOLD Страницы: 34

Бренд: Vicko Страницы: 9

Бренд: Bionaire Страницы: 10

Бренд: Convair Страницы: 8

Бренд: Frico Страницы: 14

Бренд: Warren rupp Страницы: 16

Бренд: emerio Страницы: 31

Бренд: Oasis Страницы: 40

Бренд: Graco Страницы: 14

Eco Heater HHT060

Бренд: hylite Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды