Kronoterm WP4 LF-502 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 56

background image

ID.: 17-16-20-2979-10

40

3.2018

COMFORT Plus:

Switch to programme

COMFORT Plus, when power from
solar panels is available.

Backup source:

Activation of backup source

programme.

Function input 1

Function input 2

Function input 3

7.3.15.4 Standby Setup

When water reaches desired temperature, the heating switches off and
enters standby mode until water temperature doesn't drop for the standby
level difference.

Factory setting for standby difference 7 °C.
Setting area: AUTO or 2 °C – 10 °C.
Setting step: 0,1 °C..

Example: Water heating will deactivate after reaching the desired
temperature 55 °C. Heating will reactivate once temperature drops for the
standby difference

7 °C, thus to 48 °C.

Dynamic standby

:

In case of setting the standby temperature to AUTO, the standby temperature changes in
regards to the set desired water temperature. If the temperature set is 40 °C, standby
temperature

difference is 5 °C, while in the case of water temperature 55 °C and more,

standby equ

als 10°C. Between temperatures 40 °C and 55 °C the standby temperature

difference is calculated in a linear way between 5 and 10 °C.

Static standby

:

Other standby settings are static and are the same for all water temperatures. The minimal
temperature difference is thus 2 °C, and the maximal 10 °C. Factory standby difference is set
to 7 °C.

7.3.15.5 Temperature Settings for PHOTOVOLTAICS Programme

Device in the programme PHOTOVOLTAICS - PV (solar photovoltaic
system) (chapter 8.3.4) heats sanitary water to PV temperature setting.

The factor

y setting is 70 °C.

Setting range: 55 °C – 75 °C.
Setting step: 0,5 °C..

7.3.15.6 Standby in PHOTOVOLTAICS Programme

When the temperature of sanitary water in the programme PV (chapter 8.3.4)
drops under the set desired temperature for the programme PV for the
temperature deviation value (»Standby in PHOTOVOLTAICS Programme«),
the device resumes heating the sanitary water.

Factory temperature deviation setting is 3 °C
Setting range: 1 °C – 20 °C.
Setting step: 0,1 °C

«
...
38
39
40
41
42
...
»

Содержание WP4 LF-502

























































Отзывы:

Нет отзывов

Похожие инструкции для WP4 LF-502

Бренд: Ebsray Страницы: 12

Бренд: VARISCO Страницы: 16

Бренд: Macnaught Страницы: 12

Бренд: Easy@Home Страницы: 42

Бренд: Ariston Страницы: 88

Бренд: alkitronic Страницы: 12

SMART ECG 1000 A

Бренд: Airtecnics Страницы: 22

Бренд: Clarke Страницы: 12

Elnur ECOMBI HHR Series

Бренд: Gabarron Страницы: 17

Бренд: Honda Страницы: 25

Бренд: Barmesa Pumps Страницы: 15

Бренд: EQUATION Страницы: 48

Бренд: Sunbeam Страницы: 12

AQUAJET PFN 10000 PLUS

Бренд: Aquael Страницы: 54

Бренд: Waterax Страницы: 5

Бренд: Giant Страницы: 12

Бренд: Somogyi Elektronic Страницы: 23

Бренд: Watson Marlow Pumps Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды