manualshive.com logo in svg

Krone 5XL-R/GL, Оригинальная инструкция по эксплуатации, Страница: 81 / 154

Поделиться
Скачать
Krone 5XL-R/GL Скачать руководство пользователя страница 81

IV - 39

Control Unit

4.9.2 Logical alarm messages

 

No. Screen

Description

Possible cause

Remedy

1 

Wagon is full 

Tailgate is closed and the floor 
conveyor switch-off unit sensor is 
switched 

Empty wagon 

2 

Discharge roller 
speed too 
slow/discharge 
rollers stopped 

The wagon is full, the tailgate is open, 
floor conveyor supply is activated and 
discharge roller speed is too slow 

Check the discharge 
roller drive 

For ZX: 

The wagon is full, the tailgate is open, 
floor conveyor supply is activated and 
discharge roller speed is too slow 

The tailgate is open, the floor 
conveyor supply is activated and the 
PTO shaft is not activated 

- Discharge roller drive 
stopped 

- Switch on PTO shaft 

3 

PTO shaft speed 
too high 

PTO shaft is not stopped and an 
attempt was made to open the tailgate

Switch off the PTO 
shaft first. Do not open 
the tailgate until the 
PTO shaft is turned off 

4 

Steering axle not 
locked 

The tailgate was opened and the 
steering axles was not locked 

Lock the steering axle 
before opening the 
tailgate (lock the 
steering axle on the 
silo pile!) 

11 

Blades have not 
been turned on 
(blade monitor) 

Blades have moved out of the “Blade 
on“ position 

Switch blade back on 

12 

PTO shaft not 
correctly set or 
defective 

The discharge rollers are turning but 
the PTO shaft sensor is not 
generating any pulses 

Check the setting of 
the PTO shaft sensor 

13 

Electrical/hydraulic 
axle suspension is 
not active 

The electrical/hydraulic axle 
suspension is not in Automatic mode 
during loading (pick-up in float setting)

Activate 
electrical/hydraulic 
axle suspension 

14 

Tailgate is open 

Tailgate has been opened even 
though the key for “Open tailgate” has 
not been activated 

Close tailgate 

15 

Axle is not locked

 

 

Axle is not locked even though the key 
for "Lock axle" has been actuated.

 

Check the hydraulics

 

Check the manometric 
switch

 

 

16 

Hand lever for 
discharge roller 
coupling not 
actuated.

Tail control is turned on but the hand 
lever for discharge roller coupling has 
not been switched to the zero 
position.

Actuate the hand lever

17 

Switching valve to 
release the cross 
conveyor has not 
been actuated.

Tail control is turned on but the 
switching valve to release the cross 
conveyor has not been actuated.

 

Actuate the switching 
valve

 

 

Содержание 5XL-R/GL



























































































































































Отзывы:

Нет отзывов