Krone 5XL-R/GL Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 154

Krone 5XL-R/GL Скачать руководство пользователя страница 30

III - 6

Operation

KR-1-080

2

1

3.4.5 Articulated shaft

• Push the articulated shaft (1) onto the tractor power

take-off shaft.

The safety catch must click into place

(see the articulated-shaft
manufacturer’s operating
instructions).

• Attach the retainer chains (2) of the guard to the

articulated shaft.

• Always install the overload coupling on the machine

(wagon) side.

• see A1 "Initial hitch up".

3.4.6 Hydraulic connection for blocking

trailing steering axle (special fitting)

Connect the separate hydraulic hose from the arrester
ram of the steering axle (yellow protective cap) to a
single-acting connection on the tractor hydraulic system.

Follow the tractor manufacturer’s user
instructions for the parallel operation
of tractor control equipment.
The supply to the connection for the
arrester ram of the trailing steering
axle must take precedence over or be
of equal precedence to the other
hydraulic supply to the loading/
metering wagon.

3.4.7 Drawbar-suspension (special fitting)

The drawbar-suspension consists of a hydro
accumulator, which absorbs the pressure peaks in the
offset drawbar-cylinder. To guarantee the function of the
drawbar suspension, the offset drawbar-cylinders must
be extended by about 20mm.

«
...
28
29
30
31
32
...
»

Содержание 5XL-R/GL



























































































































































Отзывы:

Нет отзывов