Krone 5XL-R/GL Скачать руководство пользователя страница 68

Страница: 68 / 154

IV - 26

Control Unit

4.7.12 Menu 2-2 "Total counters"

Calling the menu

Main menu

2 "Counters" is displayed

• You can select menu 2-2

with the rotary

potentiometer. The icon is shown in reverse colours.

• Press the rotary potentiometer.

The display shows menu 2-2 "Total counters". The total
number of wagonloads is the sum of all wagonloads.
They are not assigned to any customer counter.
Meaning of the icons:

•

= Total number of wagonloads

•

= Operating hours counter

•

= Total wagonload counter (cannot be

deleted).

•

= Season counter 1 (can be deleted)

•

= Daily counter 2 (can be deleted)

Deleting season counter 1 or daily counter 2

• Press the

key for softkey

Season counter 1 is set to zero.

• Press the

key for softkey

Daily counter 2 is set to zero.

• Use the

key to close the menu currently

displayed.

The display shows menu level

2 "Counters".

• Pressing the

key and holding it down brings up

the basic screen.

L400150

The total operating hours counter (1) is
running as soon as the electronics is
turned on. The total operating hours
counter (1) cannot be deleted.

ZX000022

Содержание 5XL-R/GL



























































































































































Результаты поиска

Содержание 5XL-R/GL

Отзывы:

Krone 5XL-R/GL, Оригинальная инструкция по эксплуатации, Страница: 68 / 154

Результаты поиска

Содержание 5XL-R/GL

Отзывы: