Krone 5XL-R/GL Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 154

Krone 5XL-R/GL Скачать руководство пользователя страница 33

III - 9

Operation

3.7.3 Setting the cutting length

This adjustment is carried out centrally on the left hand
side of the wagon.

• Lowering the cutter unit (see chapter 4 page IV-7)
• Remove the ignition key and switch off the electrical

supply at the control box.

• Using the multipurpose spanner (4), switch the

cutters in or out until the desired number of cutters
and therefore the desired cutting length has been
selected.

• Hang the multipurpose spanner in the transport

retainer again.

• Follow instructions in 3.7.6.
• Switch on the electrical system again.
• Bring the cutter back into the working position (see

chapter 4, page IV-7)

3.7.4 Switching cutters

Lifting the articulated tow-bar makes it

easier to work in comfort under the
vehicle. Secure the raised vehicle with the
supporting foot.

Lower the cutter unit fully

• Bring blade bar into maintenance position (see

chapter 4, page IV-7)

Remove the ignition key and switch off
the electrical supply at the control box.

The safety lever (6) on each cutter safety device must
be released in order to remove the cutters (5). For this
purpose, the multipurpose spanner (4) must be used to
rotate both selector shafts so that their cams (1) and (2)
are pointing downwards.
The blades (5) can now be removed.

Wear protective gloves while taking out/
attaching the cutters!

KDW00031

ON

OFF

KDW05142

«
...
31
32
33
34
35
...
»

Содержание 5XL-R/GL



























































































































































Отзывы:

Нет отзывов