Krone 5XL-R/GL Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 154

Krone 5XL-R/GL Скачать руководство пользователя страница 52

IV - 10

Control Unit

4.5.2 Basic screen image "Unloading operation"

For a general description, see Chapter 4.5.1
"Loading operation"

Differences compared to loading operation.

Displays in the main window:

•

currently set floor conveyor supply

speed in % (only for GD)

Set floor conveyor supply speed

• Turn the rotary potentiometer to set the required

floor conveyor supply speed and save the speed by
pressing the potentiometer down.

ZX000016

•

Switch the working floodlight on/off
The activated mode is shown.

Switching the working floodlight on

Press the

key for softkey

Switching the working floodlight off

Press the

key for softkey

Softkeys

•

Switching to loading/unloading operation
(during deactivated automatic unloader /
setting refer to Chapter "Automatic unloader")
The activated mode is shown.

Switching to loading operation

Press the

key for softkey

.

•

Switching to loading/unloading operation
(during activated automatic unloader /
setting refer to Chapter "Automatic
unloader")
The activated mode is shown.

Switching to loading operation

Press the

key for softkey

.

«
...
50
51
52
53
54
...
»

Содержание 5XL-R/GL



























































































































































Отзывы:

Нет отзывов