background image

36 

This function locks the keys to avoid unsupervised operation. A lock icon will 
appear on the LCD display screen once activated. 

 

To Activate: 

Press the 

mode key

 and 

up key

 at same time.

 

To De-activate: 

Press the 

mode key

 and 

up key

 at same time. 

15.10 

Key Lock 

Figure 15.7, Key Lock Indicator 

15.8 

Fan Speed Control  

Fan speed can be adjusted through six (6) speeds. A single ‘beep’ will confirm 
reception of the command. To activate this function,  
1.  Press the 

mode key

 to index to the fan control icon. 

2.  Press the 

up 

or 

down arrow keys 

to turn on, off, or to adjust fan speed. 

Thermostat Mode: 

Fan(s) have a five (5) minute delay time when fireplace 

is lit, allowing time for heat to build in fireplace before operating. The fan  will 
continue to operate for approximately twelve (12) minutes after fireplace has 
been turned off.   

Manual Mode: 

 Fan(s) will operate at previous setting. There is no delay in 

start up or stop time.    

Figure 15.5, Fan Remote Operation 

The light intensity can be adjusted through six (6) levels. A single beep will con-
firm reception of the command. 
1.  Press the 

 mode key

 to index to 

light 

icon. 

2.  Press the 

up 

or 

down arrow keys

 to adjust the intensity level.  

15.9 

Accent Light Kit

 

Figure 15.6, Accent Light Remote Operation 

Remote control battery lifespan depends on various factors including battery 
quality, number of ignitions, changes to room thermostat set point, etc.  

 

When the remote control batteries are low, a battery icon will appear on 
the LCD display before all battery power is lost. 

 

 

When batteries are replaced, this icon will disappear. 

15.11 

Low Battery Detection 

Figure 15.8, Low Battery Indicator 

The backup battery pack is used when the electrical power to the appliance is interrupted. The lifespan of backup batteries 
depends on various factors including battery quality, number of ignitions, changes to room thermostat set point, etc.  

 

When backup batteries are low, a double-beep will be emitted from the IFC control module when it receives an ON/OFF 
command from the remote control. This is an alert for a low battery condition of the backup batteries and after this double-
beep warning, no commands will be accepted until batteries are replaced.  

 

When batteries are replaced, a beep will be emitted from IFC control module as soon as powered. 

 

15.11.1 

Remote Control 

15.11.2 

Backup Battery Pack 

Содержание Slayton 42S



















































Отзывы: