kozy heat Slayton 42S страница 33 Скачать руководство пользователя

Страница: 33 / 50

Figure 13.6, Control Board Removal and Installation

1. Shut off main gas line to appliance.

2. Remove glass frame assembly and safety barrier.

3. Disconnect gas line flex tube from manual shut-off on the valve.

4. Unplug all components from receptacle, disconnect all wiring

harnesses attached to gas valve.

5. Remove glass media.

6. Remove burner cover (secured with [10] screws).

7. Remove burner venturi housing. Remove burner tube from

mounting cradles.

8. Remove (2) nuts securing light bar to control board, carefully move

light bar backwards far enough to clear board.

9. Remove (8) screws securing control board, lift board out of firebox

being careful not to damage sealing gasket lying underneath.

1. Place control board in firebox, aligning holes in board to holes in

firebox bottom.

MAKE SURE SEALING GASKET IS IN PLACE ON FIREBOX

BOTTOM!

Secure with (8) screws previously removed.

2. Reinstall light bar onto control board, secure with (2) nuts

previously removed.

3. Reinstall burner, positioning burner venturi over burner orifice, align-

ing burner tube with mounting cradles on control board. Re-install
burner venturi housing.

4. Reinstall burner cover, aligning holes in cover to corresponding

holes in burner tube mounting cradles. Secure with screws (10).

5. Reinstall glass media, being careful not to block pilot.

6. Reconnect gas line to manual shut-off on the valve.

7. Reconnect all wiring harnesses to gas valve, Plug all components

into electrical outlet.

8. Reinstall glass frame assembly and safety barrier.

9. Turn on main gas line feeding appliance.

10. Verify proper glass media placement, operation of fireplace, and any

electrical components.

CAUTION

If burner and/or pilot have been burning, use appropriate protection to avoid burns or damage to personal property before removing any components.

WARNING

DO NOT OPERATE THIS FIREPLACE WITHOUT SEALING GASKET (LOCATED UNDER THE CONTROL BOARD) IN PLACE. IF GASKETING IS
DAMAGED, IT MUST BE REPLACED.

CAUTION

CHECK ALL CONNECTIONS FOR LEAKS WITH SOAPY WATER, WHETHER FIELD OR FACTORY MADE.

13.5

Control Board

13.5.1

Control Board Removal

13.5.2

Control Board Installation

Pilot

Burner orifice

Содержание Slayton 42S



















































Результаты поиска

Содержание Slayton 42S

Отзывы:

Похожие инструкции для Slayton 42S

Бренды по названию

Популярные бренды

kozy heat Slayton 42S, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Slayton 42S

Отзывы:

Похожие инструкции для Slayton 42S

Бренды по названию

Популярные бренды