Korenix JetNet 4500 Series Скачать руководство пользователя страница 66

Страница: 66 / 69

Korenix JetNet 4500 Series Industrial Managed Ethernet Rail Switch User’s Manual

B-2

64 VLAN groups in maximum.

Port Mirror

Support TX only, both of TX and RX packets

Packet filter

4 types of packet filter rule with different packet combination by all packets,

Broadcast/ multicast/ unknown unicast packet, broadcast/ multicast packet

or broadcast packet only.

DIP Switch

JetNet4508: 1 x 6-pin DIP Switch

DIP switch #1 ~#5:Port Link Down Alarm Enable (On)/ Disable(Off)

DIP switch #6:Ring Master Enable(On)/Disable(Off)

Relay Alarm

Dry Relay output with 1A@24V ability.

Network Redundancy

Super Ring

Recovery time less than 300ms and compatible with JetNet3500,

JetNet4000 and JetNet5010G.

Coupling Ring

Provides the ability to couple 2 super rings.

Dual Homing

Provides the ability to link Super ring and RSTP with higher level switch.

Spanning Tree

IEEE802.1d Spanning Tree

IEEE802.1w Rapid Spanning Tree

Interface

Number of Ports

JetNet4508:8 x 10/100Base-TX with Auto MDI/MDI-X, Auto-Negotiation

functions.

JetNet4508f:6 x 10/100Base-TX with Auto MDI/MDI-X, Auto-Negotiation

functions.

2 x 100Base-FX

Connectors

10/100TX: 8 x RJ-45 (JetNet 4508),

10/100TX: 6 x RJ-45 + 100Base-FX: 2 x SC connectors for Multi-mode or

single mode fiber. (JetNet 4508f)

Terminal Block: 6-pin for 2 x power input and 1 relay alarm output.

DC power Jack x 1

Cables

CAT-3, CAT-4, CAT-5 unshielded twisted pair or shielded twisted pair

cable. The Link distance is 100 meters in maximum.

Fiber : 50/125um or 62.5/125 multi-mode fiber, 2KM (JetNet4508f-m)

8/125um or 9/125um single mode fiber, 30KM (JetNet4508-s)

Diagnostic LED

Per system: Power (green) x3, Ring Master (green) x1, Alarm (red) x1

Per RJ-45/Fiber port: Link (green on)/Activity(green flashing), Full duplex

(Yellow on) /Collision (Yellow blinking)

Power Requirements

System Power

2 power input by terminal block with redundancy

Input Voltage: DC 24V (12~48V) with reverse polarity protection.

Power Consumption

JetNet4508: 4.1 Watts @ DC 24V

JetNet4508f: 6.7 Watts @ DC 24V

Mechanical

Содержание JetNet 4500 Series






































































Результаты поиска

Содержание JetNet 4500 Series

Отзывы:

Бренды по названию

Популярные бренды

Korenix JetNet 4500 Series, Руководство пользователя

Результаты поиска

Содержание JetNet 4500 Series

Отзывы:

Бренды по названию

Популярные бренды