Korenix JetNet 4500 Series Скачать руководство пользователя страница 55

Страница: 55 / 69

Korenix JetNet Series Industrial Managed Ethernet Rail Switch User’s Manual 3-37

Event Configuration

Event Types

Event Types can be divided into two basic groups: System Events and Port Events. System

Events are related to the overall function of the switch, whereas Port Events and related to the

activity of a specific ports

System Event

Warning Email is sent when…..

Device Cold start

Power is cut off and then reconnected

Power Status

One of redundant power (PWR1 or PWR2) fails

Authentication failure

An incorrect password is entered

Super Ring topology changes

If Master of Super Ring has changed or backup

path is activated

Port Event

Warning Email is sent when…..

Link-on

The port is connected to another device

Link-off

The port is disconnected (e.g. the cable is pulled out, or

the opposing devices turns down)

Содержание JetNet 4500 Series






































































Результаты поиска

Содержание JetNet 4500 Series

Отзывы:

Бренды по названию

Популярные бренды

Korenix JetNet 4500 Series, Руководство пользователя

Результаты поиска

Содержание JetNet 4500 Series

Отзывы:

Бренды по названию

Популярные бренды