manualshive.com logo in svg

Korenix JetNet 4500 Series, Руководство пользователя

Поделиться
Скачать
Korenix JetNet 4500 Series Скачать руководство пользователя страница 22

 

  Korenix JetNet 4500 Series Industrial Managed Ethernet Rail Switch User’s Manual 

3-4 

 

Super Ring 

This section is to enable and configure Super Ring, Ring Coupling & Dual homing settings. 

QoS 

This section is to enable and configure QoS(Quality of service) settings. 

IGMP 

This section is to enable and configure the JetNet’s IGMP Snooping function. 

Security Manager 

This section is to change the username and the password. 

Configuration Backup 

This section is to backup the JetNet’s settings to a file on your PC. 

TFTP Update Firmware 

This section is to use TFTP utility to update the latest firmware to the JetNet. 

Factory Default 

This section is to restore the factory default settings. 

Save Configuration 

This section is to save the JetNet’s settings. 

System Reboot 

This section is to reboot the JetNet. 

Rate Control 

This section is to set up each port’s bandwidth rate and packet limitation type. 

Alert 

This section is to set up email warning, event trap and power inputs failure alarm. 

SNMP 

This section is to set up SNMP configuration 

System Log 

This section is to set up System Log.   

 

Configuring JetNet 4500 Series Industrial Ethernet Switch 

Port Status 

 

In this window, you can see each port’s status. 

Port

: Indicates the port number. 

Type

: Indicates the speed mode of the port. For example, 100TX means 100 Mbps. 

Link

: 

Down

 Indicates that connection is not established; “

Up

” indicates that the connection is 

successfully established.   

State

: Indicates whether this port is 

Enabled

 or 

Disabled

. A disconnection is also denoted as 

Содержание JetNet 4500 Series






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды