manualshive.com logo in svg

Korenix JetNet 4500 Series, Руководство пользователя

Поделиться
Скачать
Korenix JetNet 4500 Series Скачать руководство пользователя страница 12

 

  Korenix JetNet 4500 Series Industrial Managed Ethernet Rail Switch User’s Manual 

2-2 

Introduction 

Panel Layout 

Here we use JetNet 4508f Industrial Ethernet Switch as an example. 

Front View 

 

1  LED indicators 

2  DIP switch 

3  RJ-45 ports 

4  Fiber ports 

 

Bottom View 

At the bottom of this switch is a 
ground screw and a 6-position plug-in 
terminal block connector with two DC 
power inputs and a relay connection. 
There is also a DC-IN power jack for 
connecting an optional AC-DC power 
adapter (wall transformer type). 

 

Reset Button 

The Reset button provides users with a quick and easy way to restart JetNet 4500 Series 
Industrial Ethernet Switch and restore the default settings. 

To restart: press the Reset button for 2 seconds and release. 

To restore the default settings: press the button for 5 seconds and release. 

Note that you must always restart a switch after setting its Ring Master DIP switch in order to 
activate the new DIP switch setting or the redundant ring will not operate. 

LED Indicators 

There are 9 diagnostic LEDs and 12 Port LEDs on JetNet 4508 Industrial Ethernet Switch. These 
LED indicators provide administrators with real-time system status. The following table describes 
the function of each LED indicator. 

Содержание JetNet 4500 Series






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды