Korenix JetNet 4500 Series Скачать руководство пользователя страница 21

Страница: 21 / 69

Korenix JetNet Series Industrial Managed Ethernet Rail Switch User’s Manual 3-3

Configuration via the Web-based Management Interface

Menu Bar Introduction

Home

Port Status

Port Statistics

Port Control

Switch Settings

Port
Mirroring

VLAN
Configuration

Alert

IP
Configuration

SNTP

IP Security

RSTP

Super Ring

QoS

IGMP

SNMP

Security
Manager

Configuration

Backup

TFTP Update
Firmware

Factory Default

Save
Configuration

System
Reboot

Rate Control

System
Log

Home

The home page of this embedded web-based management interface.

Port Status

This section is to display the port status and settings.

Port Statistics

This section is to display the JetNet’s port data flow statistics.

Port Control

This section is to configure the JetNet’s port settings.

Switch Settings

This section is to display the information of the JetNet’s system.

Port Mirroring

This section is to enable and configure port mirroring settings.

VLAN Configuration

This section is to enable and configure VLAN settings.

IP Configuration

This section is to set up the JetNet’s IP address.

SNTP

This section is to enable the network time server.

IP Security

This section is to set up the IP address which allows users to access the JetNet from the web.

RSTP

This section is to enable and configure the RSTP function.

Содержание JetNet 4500 Series






































































Результаты поиска

Содержание JetNet 4500 Series

Отзывы:

Бренды по названию

Популярные бренды

Korenix JetNet 4500 Series, Руководство пользователя

Результаты поиска

Содержание JetNet 4500 Series

Отзывы:

Бренды по названию

Популярные бренды