manualshive.com logo in svg

Korenix JetNet 4500 Series, Руководство пользователя

Поделиться
Скачать
Korenix JetNet 4500 Series Скачать руководство пользователя страница 45

 

 

 

Korenix JetNet Series Industrial Managed Ethernet Rail Switch User’s Manual  3-27

The IEEE 802.1D suggests you to use CoS value 0 and 3 to Low, 1 and 2 to Lowest, 4 and 5 to 
Middle, 6 and 7 to High. 

 

ToS-Queue Mapping 

TOS is also known as DSCP. This is the field in the IP TOS packet. If the L3 switch or Router use 
this field as the QoS service. Then the L2 switches attached to the network should have the 
same policy as the L3 switch or Router. This table allows you to configure the queue level for 
each DSCP value. 

 

 
IGMP Snooping 

 

The IGMP (Internet Group Management Protocol) is an Internet Protocol that provides a way for 
an internet device to report its multicast group membership to adjacent routers. Multicasting 
allows one computer on the internet to send data to a multitude of other computers that have 

Содержание JetNet 4500 Series






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды