manualshive.com logo in svg

Korenix JetNet 4500 Series, Руководство пользователя

Поделиться
Скачать
Korenix JetNet 4500 Series Скачать руководство пользователя страница 39

 

 

 

Korenix JetNet Series Industrial Managed Ethernet Rail Switch User’s Manual  3-21

How to Set Up a Super Ring? 

 

Here we use 4 JetNet 4508 Industrial Ethernet Switches to form a Super Ring topology. Switch 1 
is configured to be the Ring Master, and the 1

st

 Ring Port of the R.M. is the forwarding/primary 

path, the 2

nd

 Ring Port of R.M. is the backup path. R.M. will continuously sent hello packet 

through port 3 to next switch and receive the returned hello packet from port 4.   

 

The settings of Switch 1, Ring Master.   

Click the R.M. DIP to ON. The web UI will show The switch is Ring 
Master. Port 3 and Port 4 are the Ring Ports. 

 

The settings of Switch 2. 

The Port 1 and Port 8 are the Ring Ports. The 2 ports of non-R.M. are 
forwarding ports. 

 

The settings of Switch 3. 

The Port 3 and Port 4 are the Ring Ports. The 2 ports of non-R.M. are 
forwarding ports. 

 

Содержание JetNet 4500 Series






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды