manualshive.com logo in svg

Korenix JetNet 4500 Series, Руководство пользователя

Поделиться
Скачать
Korenix JetNet 4500 Series Скачать руководство пользователя страница 48

 

  Korenix JetNet 4500 Series Industrial Managed Ethernet Rail Switch User’s Manual 

3-30 

TFTP Update Firmware 

 

In this section, you can update the latest firmware for your JetNet 4500 Industrial Ethernet 
Switches. Before you do so, make sure that you have your TFTP server ready, and the firmware 
image is already installed on the TFTP server. 

TFTP Server IP Address

: Type in the IP address of your TFTP server here. 

Firmware File Name

: Type in the file name of the firmware image. 

Once you finish configuring the settings, click on 

Apply

 to apply your configuration. 

Note: 

Remember to click on the 

Save Configuration

 button to save your settings. Otherwise, 

the settings you made will be lost when the JetNet is powered off.   

 

Factory Default 

 

In this section, you can reset the JetNets to the default settings as shown below:   

Default IP address:

 192.168.10.1

 

Default Gateway: 

192.168.10.254 

Subnet Mask: 

255.255.255.0 

Other switch settings will be set to disable or none. 

Click on 

Default

 to reset your JetNets to the default settings.   

Note: 

This provides a quick method for clearing the JetNet’s internal settings. However, it will not 

restore the IP address to the default settings. If you want to restore all the settings to their default 
state, including the IP address, please use the reset button on the front panel of your JetNet 

Содержание JetNet 4500 Series






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды