Kontron CP3010-SA Скачать руководство пользователя | Manualshive

Страница: 16 / 80

background image

D R A F T — F O R I N

T E R N A L U S E O N L Y

16

www.kontron.com

User Guide

CP3010-SA

1.4 Technical Specif ication

Table 1: CP3010-SA Main Specifications

FEATURES

SPECIFICATIONS

SoC

CPU

The CP3010-SA supports the following processors:

» Quad-core Intel® Atom™ E3845, 1.91 GHz, 2 MB L2 cache
» Dual-core Intel® Atom™ E3827, 1.75 GHz, 1 MB L2 cache

Graphics Controller

Intel® HD Graphics integrated in the processor with support for two independent
displays

Mem

or

y

Main Memory

Up to 8 GB, dual-channel DDR3L SDRAM memory without ECC running at 1333 MHz
(soldered)

Flash Memory

Two 8 MB SPI boot flash chips for two separate uEFI BIOS images
SATA NAND flash (optional):

» Up to 64 GB soldered SATA NAND flash, or
» CFast card

EEPROM

EEPROM with 64 kbit

Inter

faces

CompactPCI

CompactPCI interface:

» Compliant with CompactPCI Specification PICMG® 2.0 R 3.0
» System master operation
» 32-bit / 33 MHz master interface (66 MHz on request)
» 3.3 V or 5 V (universal PCI interface)
» Support for up to seven peripheral slots (7x REQ/GNT signals)

When installed in a peripheral slot, the CP3010-SA is isolated from the CompactPCI
bus. It receives power from the backplane and supports rear I/O.

CP3010-SA removal under power:
When installed in a peripheral slot, the CP3010-SA supports hot plugging on the
power interface through a dedicated power controller, but not on the PCI inter-
face.

Hot swapping of peripheral boards controlled by the CP3010-SA:
When installed in the system slot, the CP3010-SA supports the hot swapping of
other boards. Individual clocks for each slot and Enum signal handling are in com-
pliance with the PICMG 2.1 Hot Swap Specification.
The CP3010-SA itself, however, is not hot swappable. When installed in the system
slot, the system must be powered down in order to replace the board.

Rear I/O

The following interfaces are routed to the rear I/O connector J2:

» COMA and COMB, or COMA and GPIO (all ports have 3.3V LVTTL signaling)
» General purpose signals: 5 x GPIs and 3 x GPOs
» 2  x  USB  2.0
» 1  x  CRT  VGA
» 2 x Gigabit Ethernet
» 2  x  SATA  3Gb/s
» System management signals
» Input for 5V standby power
» System write protection

«
...
14
15
16
17
18
...
»

Содержание CP3010-SA

















































































Отзывы:

Нет отзывов

Похожие инструкции для CP3010-SA

Бренд: Conceptronic Страницы: 2

Бренд: Sunpak Страницы: 8

Бренд: OBID Страницы: 38

Бренд: TRENDnet Страницы: 15

Sentinel-Prox DC-1023

Бренд: AWID Страницы: 12

RossGear AFR-7814C

Бренд: Ross Страницы: 16

ADIO1600 Series

Бренд: ICS Advent Страницы: 72

Бренд: Jamex Страницы: 15

PISO-CAN-FD Series

Бренд: ICP DAS USA Страницы: 88

Traveldrive 1000&1

Бренд: Hama Страницы: 22

Бренд: ZKTeco Страницы: 11

Бренд: AuviTran Страницы: 19

Бренд: IDTECK Страницы: 26

Бренд: IDTECK Страницы: 51

Бренд: Kantech Страницы: 26

Бренд: RocketFish Страницы: 2

9500GT 1GB DDR2

Бренд: Gainward Страницы: 2

Бренд: Icidu Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды