Kontron CP3010-SA Скачать руководство пользователя | Manualshive

Страница: 72 / 80

background image

D R A F T — F O R I N

T E R N A L U S E O N L Y

72

www.kontron.com

User Guide

CP3010-SA

9.2.3 Security Setup Menu

The Security Setup menu provides information about the passwords and functions for specifying the
security settings. The passwords are case-sensitive. The CP3010-SA provides no factory-set passwords.

Note:

If there is already a password installed, the system asks for this first. To clear a password,
simply enter nothing and acknowledge by pressing <RETURN>. To set a password, enter it
twice and acknowledge by pressing <RETURN>.

9.2.3.1 Remember the Password

It is highly recommended to keep a record of all passwords in a safe place. Forgotten passwords may
lead to being completely locked out of the system.

If the system cannot be booted because neither the User Password nor the Supervisor Password are
known, refer to the Chapter 3.1, DIP Switch Configuration, for information about clearing the uEFI
BIOS settings, or contact Kontron for further assistance.

Note:

The HDD security passwords cannot be cleared using the above method.

Table 49: Security Setup Menu Functions

FUNCTION

DESCRIPTION

Supervisor Password is:

Read-only field.

User Password is:

Read-only field.

Set Supervisor Password

Sets or clears the Supervisor Password

.

Supervisor Hint String

Press “Enter” to specify a hint string for the Supervisor Password.

Set User Password

Sets or clears the User Password

.

User Hint String

Press “Enter” to specify a hint string for the User Password.

Min. password length

Specifies the minimum password length.

Authenticate User on Boot

Enables the user authentication prompt on the boot.

HDD Password Select

Specifies whether to enable User-only support for HDD or User and Master support.

HDD00 Password State

Read-only field.

Set HDD00 User Password

Specifies and confirms the HDD User Password.

Set HDD00 Master Password

Specifies and confirms the HDD Master Password.

TPM Support

Enables/Disables TPM support.

Table 50: TPM Configuration Sub-Screen

FUNCTION

DESCRIPTION

Current TPM State

Read-only field.

TPM Action

Enacts TPM Action.
Note: Most TPM actions require TPM to be Enabled to take effect.

Omit Boot Measurements Enabling this option causes the system to omit recording boot device attempts in PCR[4].

«
...
70
71
72
73
74
...
»

Содержание CP3010-SA

















































































Отзывы:

Нет отзывов

Похожие инструкции для CP3010-SA

Бренд: Nedap Страницы: 40

Бренд: Sunpak Страницы: 8

Бренд: PERCo Страницы: 22

ATI Radeon 2400PCI256T

Бренд: Diamond Multimedia Страницы: 1

Бренд: Cognex Страницы: 35

Бренд: ATCOM Страницы: 15

Бренд: Identiv Страницы: 40

Бренд: TransCore Страницы: 2

USB CompactFlash

Бренд: Memorex Страницы: 4

Бренд: SMC Networks Страницы: 44

ULTRA 485+2.PCI

Бренд: SeaLevel Страницы: 23

Бренд: Gadget Labs Страницы: 20

XtremeLC Series

Бренд: EMS Imaging Страницы: 15

Бренд: Invengo Страницы: 56

Бренд: Rosslare Страницы: 2

Бренд: IDTECK Страницы: 8

Бренд: IDTECK Страницы: 13

Бренд: IDTECK Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды