manualshive.com logo in svg

Kontron CP3010-SA, Руководство пользователя

Поделиться
Скачать
Kontron CP3010-SA Скачать руководство пользователя страница 70

D R A F T   —   F O R   I N 

T E R N A L   U S E   O N L Y

70

www.kontron.com

User Guide

CP3010-SA

9.2   Setup Menus

The Setup utility features four menus listed in the selection bar at the top of the screen:

»

Main

»

Advanced

»

Security

»

Boot

»

Exit

The Setup menus are selected via the left and right arrow keys. The currently active menu and the cur-
rently active uEFI BIOS Setup item are highlighted in white. Each Setup menu provides two main
frames. The left frame displays all available functions. Functions that can be configured are displayed
in blue. Functions displayed in gray provide information about the status or the operational configu-
ration. The right frame displays an Item Specific Help window providing an explanation of the respec-
tive function.

9.2.1   Main Setup Menu

Upon entering the uEFI BIOS Setup program, the Main Setup menu is displayed. This screen lists the
Main Setup menu sub-screens and provides basic system information as well as functions for setting
the system time and date.

Table 47: Main Setup Menu Sub-Screens and Functions 

SUB-SCREEN

FUNCTION

DESCRIPTION

System Information BIOS Version, Build 

Time, etc.

Read-only field. 
Displays information about the system BIOS, processor, memory, etc.

Boot Features

CSM Support

Enables/Disables Compatibility Support Module

Quick Boot

Enables/Disables time-optimized POST, causing certain preconfigured 
OEM optimizations to be made when the system boots. 

BIOS Level USB

Enables/Disables backward compatibility for legacy BIOS services.

Console Redirection

Enables/Disables console redirection over serial port.

Com Port

Selects the specific COM port
The COM1 port corresponds to the COMA port.
The COM0 port corresponds to the COMB port.

Terminal Type

Selects the terminal type to be emulated.

Baudrate

Selects the baud rate of the serial port.

Flow Control

Specifies the type of flow control to be used for the serial port.

Continue C.R. after 
POST

Enables/Disables console redirection after the operating system has 
loaded.

UEFI Boot

Enables/Disables uEFI Boot.

Legacy Boot

Enables/Disables Legacy Boot.

Boot Priority

Selects the priority of boot option between uEFI Boot and Legacy Boot.

Содержание CP3010-SA

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды