Kontron CP3010-SA Скачать руководство пользователя | Manualshive

Страница: 27 / 80

background image

D R A F T — F O R I N

T E R N A L U S E O N L Y

27

www.kontron.com

User Guide

CP3010-SA

2.7.5 Gigabit Ethernet

The CP3010-SA board includes three 10Base-T/100Base-TX/1000Base-T Ethernet ports based on three
Intel® I210-IT Ethernet controllers (two onboard and one on the CP3010-HDD extension module). All
three controllers are connected to the x1 PCI Express interfaces of the Intel® Atom™ processor. Two
Gigabit Ethernet interfaces are individually switchable between front I/O and rear I/O and provide
Wake-on-LAN support. One interface is available on the high-speed I/O extension connector, J7, for
the CP3010-HDD module.

Note:

In order to use the Wake-on-LAN feature, the power supply must not be switched off (+5V
stand-by voltage cannot be used). The CP3010-SA does not turn off the main power supply
after an operating system shutdown in order to support Wake-on-LAN.

Two of the Gigabit Ethernet interfaces are implemented as a standard RJ-45 Ethernet connectors,
J10A/B on the front panel.

2.7.6 SATA Interfaces

The CP3010-SA provides two SATA ports:

»

One SATA 3 Gb/s port either onboard for the SATA Flash or the CFast card, or on the Compact-
PCI rear I/O interface

»

One SATA 3 Gb/s port either on the CompactPCI rear I/O interface or on the high-speed I/O
extension connector, J7, for the CP3010-HDD extension modules

2.7.7 Debug Interface

The CP3010-SA provides several onboard options for hardware and software debugging, such as:

»

Four bicolor general purpose LEDs (LED0..3), which indicate hardware failures, uEFI BIOS
POST codes and user-configurable outputs

»

One JTAG connector, J4, for programming the onboard logic

»

One XDP-SFF, processor JTAG connector, J12, for facilitating the debug and uEFI BIOS soft-
ware development

2.7.8 CompactPCI Interface

The CP3010-SA supports a flexible CompactPCI interface with a hot plug power interface (no PCI hot
swap). In the system slot the PCI interface is in transparent mode, and in the peripheral slot the Com-
pactPCI interface is isolated so that it cannot communicate with the CompactPCI bus. This mode is
known as "passive mode".

2.7.8.1 Board Functionality when Installed in System Slot

In a system slot, the CompactPCI interface is provided as 32-bit / 33 MHz (66 MHz on request) PCI in-
terface. The CP3010-SA supports up to seven peripheral slots through a CompactPCI backplane.

«
...
25
26
27
28
29
...
»

Содержание CP3010-SA

















































































Отзывы:

Нет отзывов

Похожие инструкции для CP3010-SA

AirPro DWL-A520

Бренд: D-Link Страницы: 8

AirPro DWL-A520

Бренд: D-Link Страницы: 63

Бренд: Gallagher Страницы: 13

OBID classic-pro ID CPR.03.20-CD

Бренд: Feig Electronic Страницы: 40

Бренд: Belkin Страницы: 2

Бренд: Hauppauge Страницы: 2

Бренд: Velleman Страницы: 23

Бренд: Salto Страницы: 5

Бренд: Velleman Страницы: 23

Бренд: KWorld Страницы: 21

Traveldrive 1000&1

Бренд: Hama Страницы: 22

Бренд: Psion Teklogix Страницы: 20

Бренд: Alpha Страницы: 14

Video-PX7600GS-256

Бренд: Jaton Страницы: 25

Бренд: Corzus Страницы: 3

Бренд: KlipXtreme Страницы: 9

Бренд: Verifi Страницы: 8

Бренд: Rendaysa Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды